Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 release

Repair and operation of the car


Suzuki Grand Vitara
+ General information
+ Maintenance and lubricant
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft / bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
- Engines
   - Mechanical part of the G16 engine
      + General description
      - Routine maintenance
         Check of a compression
         Check of depression of the engine
         Check of pressure of oil
         Valvate gap
         The filtering element of the air filter
         Cover of a head of cylinders
         Case of butterfly valves and inlet collector
         The collector of the fulfilled gases
         Belt of the drive of the gas-distributing mechanism and the tension device for a belt
         Oil pan and grid of the oil pump
         Oil pump
         Valve yoke, axis of yokes and cam-shaft
         Valves and head of the block of cylinders
      + Piston rod, piston rings, rods and cylinders
      Special tool
      Necessary service materials
      Technical characteristics of the rotating inhaling moment
   + Mechanical part of the J20 engine
   + Cooling of the engine
+ Fuel system
+ System of ignition
+ System of start
+ System of release
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment

9df16362

Oil pan and grid of the oil pump

Components

1 — an oil pan
2 — a grid of the oil pump
3 — a sealant
4 — laying of a drain stopper
5 — a drain stopper
6 — the sensor of an angle of rotation of the crankshaft

7 — an oil pan nut
8 — an oil pan bolt
9 — a bolt of the sensor of an angle of rotation of the crankshaft
10 — a bolt of a grid of the oil pump
11 — a bolt of an arm of a grid of the oil pump


Apply sealant 99000-31250 on the interfaced surfaces of an oil pan and the block of cylinders, having addressed the subsection Installation.
The rotating inhaling moment.
Not to reuse.

Removal

 PERFORMANCE ORDER

    Lift the vehicle. Remove the case of forward differential (1) with differential (2), having addressed the Section Removal in the Head Forward differential.
1 — the case of forward differential
2 — differential
3 — an oil pan
    Disconnect the coupling of the sensor of an angle of rotation of the crankshaft and remove the sensor of an angle of rotation of the crankshaft, having turned off its bolt (if that is available). Merge engine oil, having opened a drain stopper (2).
1 — an oil pan
2 — a drain stopper
    Remove the lower plate of the case of the coupling (the hydrotransformer case for And/T) (1).

    Remove an oil pan (3) and then a grid of the oil pump (2).

1 — the block of cylinders
2 — a grid of the oil pump
3 — an oil pan

Cleaning

 PERFORMANCE ORDER

    Clear the interfaced surfaces of an oil pan and the block of cylinders.
    Remove oil, old sealant and dust from the interfaced surfaces and in an oil pan.
    Clear a grid of the oil pump.

Installation

 PERFORMANCE ORDER

    Apply sealant on the interfaced oil pan surface continuously. "And": sealant 99000-31250.
"and" — 2 mm (0.05 inches)
"b" — 3 mm (0.12 inches)
    Place new consolidation (2) in that place.
    Establish a grid of the oil pump (1) and an oil pan (3). At first twirl a grid bolt, and then an arm bolt by the specified rotating moment.
      The rotating inhaling moment:
        bolt of a grid of the oil pump (a): 11 N • m (1.1 kg-m, 8.0 pound on foot) bolt of an arm of a grid of the oil pump (b): 11 N • m (1.1 kg-m, 8.0 pound on foot)
    After adjustment of an oil pan to the block of cylinders, insert tightening bolts and begin to tighten at the center: turn a wrench outside, twisting on one bolt at a time.
    Fasten bolts and nuts to the specified rotating moment. The rotating inhaling moment: a bolt and a nut of an oil pan (c) — 11 N • m (1.1 kg-m, 8.0 pound on foot).
    Insert new laying and a drain stopper into an oil pan (1). Fasten a drain stopper to the specified rotating moment. The rotating inhaling moment: a drain stopper (a) — 50 N • m (5.5 kg-m, 36.5 pound on foot).
    Establish the lower plate of the case of the coupling (hydrotransformer) (1).
    Install the sensor of an angle of rotation of the crankshaft (1) and connect its coupling. The rotating inhaling moment: a bolt of the sensor of an angle of rotation of the crankshaft (a) — 10 N • m (1.0 kg-m, 7.5 pound on foot).
    Install the case of forward differential with differential, having addressed the Section Installation in the Head Forward differential. Fill the case of forward differential with gearbox oil, having addressed the Section Servicing in the Head Forward differential. Fill in the engine with engine oil, having addressed the Section Engine oil and the filter in the Head Maintenance and lubricant. Check whether engine oil and gearbox oil from each connection leaks.