Suzuki Grand Vitara
+ General information
+ Maintenance and lubricant
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft / bearing of a shaft. Oil epiploon
+ Driveshafts
- Brake system
+ Brakes
+ Brake highway / hose / main cylinder of a brake
+ Forward brakes
- Parking and back brake
+ General description
- Diagnostics
Check and adjustment
Service of the vehicle
Cable of the parking brake
Brake drum
Brake shoe
Brake cylinder
Back plate of a brake
+ Anti-blocking brake system (ABS)
+ Engines
+ Fuel system
+ System of ignition
+ System of start
+ System of release
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Brake shoe
|
|
If the slip is worn-out beyond the limit, replace a boot.
If one of brake slips is worn-out to a limit, it is necessary to replace all slips at the same time.
Thickness of the brake shoe:
standard: 6.5 mm (0.24 inches)
wear limit: 3.0 mm (0.12 inches)
|
|
Never polish a slip with an emery paper. If to polish it with an emery paper, rigid particles from an emery paper will remain on a slip and can damage a drum. When it is necessary to correct a slip, replace it with new. |
|
|
Installation
|
|
See the Note at the beginning of this Chapter. |
|
|
Before installation of the brake drum, check the external diameter of a brake shoe (3). If it does not correspond to the value given below, adjust it according to specifications, having turned the regulator (4). External diameter of a brake shoe: "a" — 219.4 - 219.7 mm (8.638 - 8.650 inches).
|
|
1 — the lock lever
2 — a regulator pin |
Install the brake drum, having convinced that an internal part of the brake drum and brake shoes are free from dirt and oil.
Upon completion of works, press the brake lever with effort about 30 kg (66 pounds) from three to ten times to receive a necessary gap between a drum and a boot. Adjust a cable of the parking brake (for adjustment, address the Section Check and adjustment of the parking brake in the Head the Brake system).
Install a back central console box.
|
|
Establish a wheel and tighten wheel nuts with the specified torque of an inhaling. Torque of an inhaling: wheel nut (b): 100 N • m (10.0 kg-m, 72.5 pounds feet). |
Check and be convinced that the brake drum does not jam and brakes work correctly. Then remove the vehicle from the elevator and execute check of a brake (a foot brake and the parking brake).
|
|
Brake shoe
Removal
|
|
Execute item 1 - the 5th procedures of removal of the Section the Brake drum.
|
|
Be especially careful, establishing a returnable spring of a brake shoe. The wrong installation can lead to the fact that the spring will come off and can become the trauma reason. |
|
|
Remove the springs pressing a boot (1), having unbent the pins pressing a boot (2).
|
Remove the top returnable spring (4), assembly of the regulator (3), the lever of the regulator (5), a spring of the lever of the regulator (6), a spring of a rack (8), and a jay (7).
Remove brake shoes and the lower returnable spring of a boot (9).
Remove brake shoes and disconnect a cable of the parking brake (2) from the lever of a block of the parking brake (1).
|
|
3 — a branch pipe of a brake cable |
|
|
Remove the lever of a block of the parking brake (2) and the holder (1) from a brake shoe (3).
|
|
|
Survey
Lever of a parking boot
|
|
Examine the lever of a brake shoe and check, whether freely the movement of rather brake shoe. If it is faulty, correct or replace.
|
Assembly of the regulator
|
|
Check a carving or a ratchet of a rack and the regulator whether there is no wear, jamming and corrosion.
|
Springs
|
|
Examine are not damaged and whether springs weakened.
|
|
Examine each part with an arrow whether there is no rust. If there are malfunctions, replace.
|
|
|
Brake shoe
Address the subsection Survey of the Section Brake Drum.
Installation
|
|
Collect parts as it should be, the return to an order at removal.
|
|
1 — the lower returnable spring
2 — the lower rack |
|
|
Establish the springs holding a boot (1) having pressed down them into place and turning clamping pins (2).
|
Establish assembly of the regulator (3) and the top returnable spring of a boot (4).
Install the lever of the regulator (5), a spring of the lever of the regulator (6), assembly of a rack (7) and a spring of a rack (8).
Establish the lower returnable spring of a boot (9).
Then address the Section the Brake drum.
|
|
|
|
