Suzuki Grand Vitara + General information + Maintenance and lubricant + Heater, ventilation and conditioner + Steering - Suspension bracket - Forward suspension bracket General description + Diagnostics - Service out of a workshop Stabilizer of cross stability / plug Shock-absorber rack Cylindrical spring Limiter of the dynamic course of a suspension bracket / Rubber nest of a spring Wheel nave (including the wheel bearing) Rotation hinge/axis Suspension bracket/plug lever + Back suspension bracket + Wheels and tires + Forward driving shaft / bearing of a shaft. Oil epiploon + Driveshafts + Brake system + Engines + Fuel system + System of ignition + System of start + System of release + Transmissions + Coupling + Transfer + Forward and back differentials + Windows, mirrors, locks and security measures. Immobilizer + Electric equipment
|
Wheel nave (including the wheel bearing)
Removal
|
Lift the car and remove a wheel.
|
Remove a flange of the drive of an axis of a shaft (1) (at the all-wheel drive car) or a wheel nave cap (at the car with the drive on two wheels).
|
If there is a system of anti-blocking of brakes (ABS), remove the wheel speed sensor from a fist and the fastening plug from a rack.
Remove a bolt of a support of a disk brake and leave a support to hang.
|
Hang up the removed support of a disk brake on a wire hook or something similar that the brake hose strongly was not bent and was not overwound or not pulled out. Do not press a brake pedal when brake shoes are removed. |
|
If the brake disk is not removed hands, use 8-millimeter bolts. |
|
Remove a lock washer of the bearing of a forward wheel (1), having weakened 4 bolts (2).
|
|
By means of the special tool remove a lock-nut of the bearing of a forward wheel. Special tool: (A): 09951-16050.
|
Remove a washer of the bearing of a forward wheel.
Hands remove a wheel nave.
|
If it is not possible to remove a wheel nave manually, use special tools. |
Special tool
|
(B) — 09943-35512 (C) — 09942-15510
|
|
If at removal of a nave of a wheel the internal holder of the bearing of a wheel remains on a wheel fist axis that means breakage of the bearing of a wheel, replace a wheel nave (together with the wheel bearing). |
Remove a rotor of the sensor (1) from a nave of a wheel (2) (if there is a system of anti-blocking of brakes of ABS).
|
- Gradually and evenly extend a sensor rotor from a wheel nave.
- Do not reuse the removed sensor rotor. At installation put a new rotor of the sensor.
|
Remove nave bolts from a nave.
|
1 — a sensor rotor 2 — a wheel nave 3 — a vice 4 — the flat end of draft |
|
|
Installation
|
1 — a lock washer 2 — a bolt 3 — a bearing lock-nut 4 — a wheel bearing washer 5 — a wheel nave 6 — a bolt |
|
Insert a new pin into a nave opening. Slowly rotate it to be convinced that crenulate connections coincide with the connections made an initial bolt.
|
1 — an oil hydraulic press 2 — a nave bolt |
Establish a new rotor of the sensor (1) by means of the special tool (if there is a system of anti-blocking of brakes of ABS).
Special tool
(A): 09952-86510
(B): 09924-74510
|
Be attentive not to insert a nave of a wheel (2) on diagonal. |
|
The provision of a rotor of the sensor of speed of a wheel (1) at installation. Approximate size: 4.9 ± 0.1 mm (0.19 ± 0.004 inches). 3 — a hydraulic press
|
Establish by fingers a nave of a wheel (1) on the spindle supporting an internal holder (3).
|
Do not beat a wheel nave with the hammer or something heavy. It is so possible to break it. |
|
If it is impossible to establish a wheel nave manually, (that means that the internal holder is not leveled), remove a nave of a wheel and establish it again. |
|
1 — a wheel nave 2 — a wheel spindle 3 — an internal holder |
Establish a wheel bearing washer, and then a wheel bearing lock-nut.
|
Turning a hand a wheel nave, tighten a wheel bearing lock-nut to the specified value of the moment of an inhaling. Special tool: (A) 09951-16050. Inhaling moment: a lock-nut of the bearing of a wheel (a) — 216 N • m (21.6 kg-m, 157 pounds feet).
|
|
Lock washer (1) block a bearing lock-nut. If the opening of a blocking bolt is not leveled with an opening in a lock-nut, turn a lock-nut in the direction of tightening until they are not leveled. Inhaling moment: a blocking bolt (b) — 1.5 N • m (0.15 kg-m, 1.1 pounds feet).
|
|
For the all-wheel drive car use plastic lithium lubricant for a washer of a shaft of the forward drive and an external axis of a fist of a forward wheel. "A": lubricant 99000-25010.
|
|
For the all-wheel drive car at installation of a lock ring (1) on a shaft of the drive use a bolted opening in a drive shaft to pull out it and to turn big diameter (2) rings to the right.
|
|
At cars with system of anti-blocking of brakes of ABS check that no alien material stuck to the sensor and a rotor. Install the sensor of speed of a wheel (1) and the plug of its fastening.
Inhaling moment:
bolt of the plug of fastening (a): 10 N • m (1.0 kg-m, 7.5 pounds feet)
bolt of the sensor (b): 23 N • m (2.3 kg-m, 17.0 pounds feet)
|
|
- At installation of the sensor of speed of a forward wheel (1) do not pull and do not overwind excessively connecting wires.
- Reliably attach a sealing ring to an internal wing.
|
|
Check that there was no gap between the sensor and a fist.
|
|
Establish a brake disk and a support of a disk brake. Inhaling moment: a bolt of a support of a disk brake (e) — 85 N • m (8.5 kg-m, 61.5 pounds feet).
|
Apply sealant and establish a flange of the drive of an axis of a shaft or a cap of a nave of a wheel.
For the all-wheel drive car
|
Apply sealant on the adjoining surface of a flange of the drive of an axis of a shaft (1), then establish a flange of the drive of an axis of a shaft and tighten a flange bolt (2) to the specified value of the moment of an inhaling.
Inhaling moment:
bolt of a flange of the drive (a): 50 N • m (5.0 kg-m, 36.5 pounds feet)
"A": sealant 99000-31090
|
For the car with the drive on two wheels
|
Remove lubricant, old sealant and dirt from the adjoining surfaces of a cap of a nave of a wheel (3) and a nave (4), evenly apply waterproof sealant "A" on the cleared nave cap surface and establish a cap on a nave. "A": sealant 99000-31090.
|
|
Establish a wheel. Inhaling moment: nut of a wheel (a): 100 N • m (10.0 kg-m, 72.5 pounds feet).
|
For cars with system of anti-blocking of brakes of ABS, carry out a test trip as it is described in the Head the Anti-blocking brake system (ABS), (The table of diagnostics of malfunctions of ABS).
|
|
|
|