For installation of a fist, an oil epiploon of an axis of a fist of a wheel and the bearing of a shaft of the drive (2) execute in the return sequence of manipulation on removal, paying attention to the following.
All-wheel drive car
|
1 — a wheel fist axis 3 — a persistent washer of a shaft of the forward drive (C or D type) 4 — an internal oil epiploon 6 — an oil epiploon of a shaft of the drive With — flat type D — flange type (for a cabriolet) |
The car with the drive on two wheels
|
1 — a wheel fist axis 5 — a fist cap
|
For the all-wheel drive car
By means of the special tool install the bearing of a shaft of the drive (1).
Special tool:
(A): 09913-76010 — a persistent washer of a shaft of the drive of S type
(A): 09913-80112 — a persistent washer of a shaft of the drive of D type
Persistent washer of a shaft of the drive of A type
Size: 0 – 1 mm (0 – 0.04 inches)
Persistent washer of a shaft of the drive of V type
Size: 1.75 – 2.50 mm (0.069 – 0.098 inches)
At installation of an axis of a fist of a wheel on a fist, process the adjoining surfaces sealant. "A": sealant 99000-31110.
For the all-wheel drive car
|
Besides, fill a flute in a wheel fist axis with about ten grams of plastic lithium lubricant. "B": lubricant 99000-25010.
|
|
Tighten a wheel fist axis nut to the specified value of the moment of an inhaling. Inhaling moment: nut of an axis of a fist of a wheel (a): 50 N • m (5.0 kg-m, 36.5 pounds feet).
|
For the all-wheel drive car
Establish by pressing an internal oil epiploon.
|
By means of the special tool enter inside an internal oil epiploon until its end concerns the step surface of a fist.
Special tool:
(B): 09944-66010
(C): 09924-74510
|
For the all-wheel drive car
Apply plastic lithium lubricant on an edge of an oil epiploon and in his cavity, having filled it more, than for 60%.
Apply lithium plastic A lubricant on a shaft of the drive (2). "A": lubricant 99000-25010.
Establish by pressing a persistent washer of a shaft of the forward drive (3) on a shaft of the drive (2) if it was removed (for a persistent nut of a shaft of the drive of V type). Apply lithium plastic A lubricant on a persistent washer of a shaft of the drive. "A": lubricant 99000-25010.
Apply lithium plastic A lubricant and establish a persistent washer of a shaft of the forward drive (3) by the rounded-off party to the central party (for a persistent washer of a shaft of the drive of A type). "A": lubricant 99000-25010.
|
Type C — a flat washer Type D — a razvaltsovanny washer |
For the car with the drive on two wheels
Remove lubricant, old sealant and dirt from the adjoining surfaces of a cap of a fist (2) and fist (1), evenly apply waterproof sealant on a pure surface of a cap and establish a cap on a fist. "B": sealant 99000-31090.
|
1 — a fist 2 — a fist cap 3 — a wheel spindle |
|
Tighten a hairpin lever nut with a spherical tip. For this purpose take a new nut and tighten it to the specified value of the moment of an inhaling. Inhaling moment: a hairpin nut with a spherical tip (a): 60 N • m (6.0 kg-m, 43.5 pounds feet).
|
For the car with the drive on two wheels
|
Apply waterproof sealant on the adjoining surface of a nave of a wheel (1) and establish a cap of a nave (2) on a wheel nave. "A": sealant 99000-31090.
|
For the all-wheel drive car
|
At installation of a flange of the drive of the bridge (1) on a wheel nave, apply sealant on the adjoining surface of a flange of the drive of the bridge (1). "A": sealant 99000-31090. Inhaling moment: bolt of a flange of the drive (a): 50 N • m (5.0 kg-m, 36.5 pounds feet).
|
For installation of a nave of a wheel see in this Chapter the Section Wheel Nave (including the wheel bearing).
|
Connect a tip of steering draft to a fist and tighten a new nut of a tip of steering draft. Inhaling moment: nut of a tip of steering draft (a): 40 N • m (4.0 kg-m, 29.0 pounds feet).
|
|