Suzuki Grand Vitara
+ General information
+ Maintenance and lubricant
+ Heater, ventilation and conditioner
+ Steering
- Suspension bracket
- Forward suspension bracket
General description
+ Diagnostics
- Service out of a workshop
Stabilizer of cross stability / plug
Shock-absorber rack
Cylindrical spring
Limiter of the dynamic course of a suspension bracket / Rubber nest of a spring
Wheel nave (including the wheel bearing)
Rotation hinge/axis
Suspension bracket/plug lever
+ Back suspension bracket
+ Wheels and tires
+ Forward driving shaft / bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ System of ignition
+ System of start
+ System of release
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Suspension bracket/plug lever
Removal
|
|
Remove a cylindrical spring. See in this Chapter the Section the Cylindrical spring.
Remove bolts and nuts of the lever of a suspension bracket. Then remove the suspension bracket lever.
Carefully, not to damage the face surface of the lever of a suspension bracket, cut off a flange part of the plug of the lever of a suspension bracket (rubber and steel). A size: about 6 mm (0.236 inches).
|
|
1 — the cut-off flange
2 — the external diameter of the plug |
|
|
Put the lever of a suspension bracket and the special tool on a hydraulic press. Combine the cut-off suspension bracket lever flange with the welded part (1) of the special tool, and the party of connection with the suspension bracket lever with a step part (2) of the special tool. The special tool (A) — 09951-46020.
|
|
|
With extra care pull out the suspension bracket lever plug to press it vertically. Otherwise it is possible to be traumatized. |
|
|
Remove the forward plug, having pulled out it by means of a hydraulic press (1) and the special tool.
Special tool:
(A): 09951-46020.
(B): 09924-74510
(C): 09951-16060
|
|
|
Remove the back plug, having pulled out it by means of a hydraulic press (1) and the special tool.
Special tool:
(A): 09951-46020
(D): 09913-80112
(E): 09925-58210
|
|
|
Installation
Forward plug
By means of the special tool, press the forward plug (2) until its flange concerns edge of the case of the lever of a suspension bracket.
Special tool
(C): 09951-16060
(F): 09913-85210
|
|
Cave-in of the plug can be facilitated if to process the internal surface of the case of the lever of a suspension bracket soap water or oil with additives. |
|
|
1 — a hydraulic press
And — the flange of the plug concerns edge of the case |
Back plug
|
|
By means of the special tool, press the back plug (2) until its flange concerns edge of the case of the lever of a suspension bracket.
Special tool
(E): 09925-58210
(F): 09913-85210
|
|
Cave-in of the plug can be facilitated if to process the internal surface of the case of the lever of a suspension bracket soap water or oil with additives. |
|
|
1 — a hydraulic press
2 — the back plug
And — the flange of the plug concerns edge of the case |
Install the suspension bracket lever on the chassis.
Lower the car in situation without loading and tighten a suspension bracket lever nut to the specified value of the moment of an inhaling.
|
|
|
|
In model with the H27 engine do not reuse a back nut of the forward lever of a suspension bracket (1). |
|
Inhaling moment:
Forward nut of the lever of a suspension bracket (a): 85 N • m (8.5 kg-m, 61.5 pounds feet)
Back nut of the lever of a suspension bracket (b): 126 N • m (12.6 kg-m, 91.0 pound foot)
Further installation is similar to installation of a cylindrical spring. See in this Chapter the Section the Cylindrical spring.
|
|
|
|
