Suzuki Grand Vitara
+ General information
+ Maintenance and lubricant
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft / bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ System of ignition
+ System of start
+ System of release
- Transmissions
+ Mechanical transmission (type 1)
+ Mechanical transmission (type 2)
- Automatic transmission (4 A/T)
+ General description
+ Diagnostics of the automatic transmission
+ Precautionary measures at diagnostics of malfunctions
+ Visual survey
- Service out of a workshop
Liquid level
Liquid replacement
Oil cooler hoses
Cable of a throttle of the automatic transmission
Manual selector
Gear shifting cable
Switch (sensor) of range of transmission
The speed sensor at the exit of the automatic transmission
Interruption switch on demand
Solenoidal valves
Switch of change of food \norm
Oil cooler tubes
+ System of blocking of brakes
+ Check of system
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Solenoidal valves
Solenoidal valves of switching and solenoidal TCC valve
Check
Having disconnected hitches of an electronic control unit (RSM) and by means of a service wire, check each solenoidal valve for click existence.
G16/20 engines
|
|
1 — a service wire
2 — the disconnected sockets of an electronic control unit (RSM) |
G16/20 engines
|
Solenoidal valve pereklyucheniya-A (No. 1)
|
C51-1-2
|
|
Solenoidal valve pereklyucheniya-V (No. 2)
|
C51-1-1
|
|
TSS solenoidal valve (blocking)
|
C51-1-8
|
Removal
|
|
Take out the oil probe and lift the car.
Let's the engine cool down, remove a drain stopper from the pallet of a case and merge liquid of the automatic transmission.
Establish a drain stopper with laying. Moment of an inhaling (a): 23 N • m (2.3 kg-m, 17.0 pounds feet).
Remove an arm of an exhaust pipe and disconnect the forward driveshaft from forward differential (if is).
Remove case pallet bolts.
Remove the case pallet.
Remove tubes for oil.
Remove the solenoidal valve No. 1 (the solenoidal valve pereklyucheniya-A and In) or the solenoidal valve No. 2 (TSS solenoidal valve).
|
|
1 — a drain stopper
2 — the driveshaft |
|
|
Work check
|
Every time, removing solenoidal valves of switching and the TSS solenoidal valve (blocking) from the transmission, check their physical serviceability before installation into place.
Apply with a butterdish transmission liquid on the solenoidal valve and, having squeezed hands, check that transmission liquid from a butterdish did not come out openings of the solenoidal valve when tension of the battery is not connected.
Under the conditions described above connect tension of the battery and be convinced that liquid vigorously comes out.
| |
- If liquid does not come out vigorously at implementation of the second point of check, do not reuse this solenoidal valve.
- In the drawing check of the solenoidal valve of switching is shown at the left. Check the TSS solenoidal valve similarly.
|
Without battery tension
| |
1 — a butterdish (with transmission liquid)
2 — the solenoidal valve
3 — the battery
And — an opening (has to be dry)
In — the produced liquid |
With battery tension
| |
1 — a butterdish (with transmission liquid)
2 — the solenoidal valve
3 — the battery
And — an opening (has to be dry)
In — the produced liquid |
|
|
Installation
For installation of solenoidal valves perform the procedure of removal upside-down, paying attention to the following:
|
|
Use new laying and the Au-shaped ring.
|
Establish tubes for oil in such sequence which is shown in the drawing.
|
Use new laying of the pallet of a case.
Tighten universal flange bolts and nuts of the hinge and bolts of an arm of an exhaust pipe to the specified value of the moment of an inhaling.
Fill in transmission liquid and check its level as it is described in the Section Liquid Replacement earlier.
After a warming up of the automatic transmission check whether there is no liquid leak.
|
|
|
|
