Suzuki Grand Vitara
+ General information
+ Maintenance and lubricant
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft / bearing of a shaft. Oil epiploon
+ Driveshafts
- Brake system
- Brakes
General description
+ Diagnostics
Diagnostic table
- Check and adjustment
Drain of air from brakes
Check of free height of the brake lever
Adjustment of the light switch of brakes
Check it is superfluous the pedal course
Check of a free wheeling of the brake lever
Check of level of brake fluid
Check of a brake hose and highway
Check of the main cylinder
Check of a brake disk
Check of a brake shoe
Check of a brake boot
Check and adjustment of the parking brake
Washing of hydraulic system of brakes
Check of pressure of liquid (if the car is equipped with LSPV)
Check of operation of the brake amplifier
Specifications - torque of an inhaling
Necessary materials for service
Special tool
+ Brake highway / hose / main cylinder of a brake
+ Forward brakes
+ Parking and back brake
+ Anti-blocking brake system (ABS)
+ Engines
+ Fuel system
+ System of ignition
+ System of start
+ System of release
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Check and adjustment
Drain of air from brakes
|
|
Brake fluid is very dangerous to paint. If liquid incidentally got on the painted surface, immediately erase brake fluid and clear the painted surface. |
|
|
If the vehicle is equipped with ABS, be convinced that the ignition switch is switched-off. |
Surely pit air from the brake system as shown below when the oil hydraulic actuator is disconnected Hydraulic highways of the brake system consist of two separate contours, one for brakes of forward wheels, another for brakes of back wheels. Drain of air is necessary for a brake of the right and left forward wheel, a brake of the left back wheel and LSPV (if the car has no ABS), i.e. in 4 places (3 places for vehicles with ABS).
Without ABS
|
|
1 — 4-sided connection / 2-sided connection
2 — the main cylinder
3 — LSPV
4 — a support of the right brake
5 — a support of the left brake
6 — the cylinder of the right wheel
7 — the cylinder of the left wheel
8 — the ABS activator
• — air drain point
F — the forward party |
WITH ABS
|
|
1 — 4-sided connection / 2-sided connection
2 — the main cylinder
3 — LSPV
4 — a support of the right brake
5 — a support of the left brake
6 — the cylinder of the right wheel
7 — the cylinder of the left wheel
8 — the ABS activator
• — air drain point
F — the forward party |
|
|
Fill a tank of the main cylinder with brake fluid and support him filled in at least half during air drain.
|
|
Remove a spuskny stopper of the safety valve (1).
|
Attach a vinyl tube (2) to a spuskny stopper of the safety valve of the brake cylinder, and insert other end into a vessel (3).
|
|
Press several times on the brake lever, and then, holding the lever in the pressed state, release a spuskny stopper of the safety valve approximately on one third half of a turn.
|
|
|
When liquid pressure in the cylinder is reduced to a minimum, tighten a trigger stopper of the safety valve.
|
Repeat operation until in the hydraulic line there is no vial of air left.
|
|
When bubbles disappear, press and hold the brake lever and tighten a trigger stopper of the safety valve.
|
Torque of an inhaling
Forward brake
Back brake
Trigger stopper of the safety valve of the wheel cylinder (a): 7.5 N • m (0.75 kg-m, 5.5 pounds on foot)
Trigger stopper of the LSPV safety valve (if the car is equipped with it): 7.5 N • m (0.75 kg-m, 5.5 pounds on foot)
Then attach a trigger stopper of the safety valve.
|
|
After air drain, give liquid pressure to the pipeline and check whether there is no leak.
|
Fill up liquid level in a tank to the specified level.
Check the brake lever for "softness". If the soft lever, repeat the procedure of drain of air.
|
|
|
|
