Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1.1.2. Technical characteristics
      3.1.1.3. Sinhronizatsionnye labels timing
      3.1.1.4. Compression check
      3.1.1.5. A gazoraspredelitelnyj belt
      3.1.1.6. Натяжитель газораспределительного a belt, an asterisk
      3.1.1.7. Additional приводные belts
      3.1.1.8. A camshaft cover
      3.1.1.9. A camshaft epiploon
      3.1.1.10. An epiploon of an intermediate shaft
      3.1.1.11. Epiploons of a cranked shaft
      3.1.1.12. A head of cylinders
      3.1.1.13. Hydraulic pushers
      3.1.1.14. A flywheel
      3.1.1.15. Engine fastenings
      3.1.1.16. The oil pallet
      3.1.1.17. The oil pump and маслозаборный a branch pipe
   + 3.1.2. 5-cylinder engines
   + 3.1.3. 6-cylinder engines
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice


9df16362

3.1.1.7. Additional приводные belts
THE GENERAL DATA

Depending on model, can be established from one to three additional belts which put in action the generator, the pump of the hydraulic booster of a wheel, the water pump and the compressor of the air conditioner.

In engines ADR the tension of the basic drive a belt and drive a belt of the water pump is regulated automatically.

ENGINE ADR

Removal
PERFORMANCE ORDER
1. Note a direction of rotation of a belt.
2. In models with the air conditioner disconnect from the engine and a cross-beam a forward support of the engine, remove натяжитель a belt in a forward part of the engine and remove a belt from pulleys.
3. To remove the basic приводной a belt, ослабьте натяжитель and stop its suitable probe. Remove a belt from pulleys.
4. Stop a pulley of the pump of the hydraulic booster and unscrew bolts of a pulley of the water pump. Remove приводной a belt and two halves of a pulley.

Installation and tension adjustment

PERFORMANCE ORDER
1. Put on a belt of the water pump a pulley of the pump of the hydraulic booster, establish halves of a pulley of the water pump, tighten fixing bolts and put on a belt.
2. Put on pulleys the basic приводной a belt, turn натяжитель clockwise and get a lock core.
3. In models with the air conditioner, put on a belt pulleys of the compressor and a cranked shaft, establish натяжитель and tighten bolts.
4. Adjust a belt tension, having tightened a bolt натяжителя with a six-coal head on 25 Н.м., tighten adjusting and rotary bolts.

ALL ENGINES, EXCEPT ADR

Removal
PERFORMANCE ORDER
1. Unscrew bolts of halves of a pulley of the compressor of the air conditioner and remove a pulley together with a belt.
2. Loosen the fixing bolts of the pump of the hydraulic booster of a wheel also shift the pump towards a pulley of a cranked shaft. Remove a belt from pulleys.
3. Loosen the fixing and adjusting bolts of the generator, ослабьте a lock bolt and, turning an adjusting nut, shift the generator back. Remove a belt from pulleys.

Installation and adjustment

PERFORMANCE ORDER
1. Put on the basic belt pulleys and adjust its tension. The new belt should cave in approximately on 2,0 mm, old on 5,0 mm.
2. Tighten a lock bolt, a rotary bolt and fixing bolts.