Audi 100/A6

1990-1997 of release

Repair and car operation

Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
- 6. Fuel system
   + 6.1.2. Technical characteristics
   - 6.2. Multidot system of injection of fuel
      6.2.2. Technical characteristics
      6.2.3. The air filter
      6.2.4. An accelerator rope
      6.2.5. Elements of system of injection of fuel Motronic/Jetronic
      6.2.6. Elements of system of injection of fuel Digifant
      6.2.7. The fuel filter
      6.2.8. The fuel pump and the gauge of level of fuel
      6.2.9. A fuel tank
      6.2.10. Release of pressure from system of injection of fuel
      6.2.11. An inlet collector
      6.2.12. Check of system of injection of fuel
      6.2.13. Neetilirovannyj gasoline
   + 6.3. System of injection MPI/MPFI (6-cylinder engines)
   + 6.4. The power supply system of diesel engines
   6.5. The device of service of heating
   6.6. Diagnostics of malfunctions of system of heating
   6.7. The conditioner: not only "pluses", but also "minuses"
   6.8. Rules of service of the conditioner
+ 7. An exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice

6.2.6. Elements of system of injection of fuel Digifant THE GAUGE OF THE STREAM OF AIR

Removal

PERFORMANCE ORDER

1. Disconnect an air branch pipe and a socket of connection from the gauge.

2. Turn off fixing screws and remove the gauge.

Installation

Installation is spent upside-down removals.

POTENTIOMETER THROTTLE ЗАСЛОНКИ

Removal

PERFORMANCE ORDER

1. Disconnect a socket of connection of a potentiometer.

2. Turn off fixing screws and remove a potentiometer.

Installation

Installation is spent upside-down removals.

THE GAUGE OF TEMPERATURE OF ARRIVING AIR

The temperature gauge is a part of the gauge of a stream of air and it cannot be replaced separately.

THE VALVE OF STABILIZATION OF IDLING

Removal

PERFORMANCE ORDER

1. Disconnect a socket of connection and hoses from the valve.

2. Remove the valve.

Installation

Installation is spent upside-down removals.

THE GAUGE OF SPEED OF MOVEMENT OF THE CAR

The gauge is established on a transmission. Look subsection 9.2.7.

THE GAUGE OF DETONATION COMBUSTION OF FUEL

Removal

PERFORMANCE ORDER

1. Disconnect a connection socket.

2. Turn off a fixing bolt and remove the gauge.

Installation

Installation is spent upside-down removals.

GAUGES OF TEMPERATURE OF THE COOLING LIQUID

Arrangement of the gauge of temperature of a cooling liquid (system Digifant)

The gauge of temperature of a cooling liquid is located on a left-hand side of a head of the block of cylinders.

Removal

PERFORMANCE ORDER

1. Disconnect a socket of connection of the gauge.

2. Merge a part of a cooling liquid from the engine and unscrew the gauge.

Installation

Installation is spent upside-down removals.

THE VALVE OF SYSTEM OF COLD START OF THE ENGINE

Removal

PERFORMANCE ORDER

1. Disconnect a connection socket.

2. Disconnect a fuel tube. Turn off fixing bolts and remove the valve.

Installation

Installation is spent upside-down removals.

THE CASE THROTTLE ЗАСЛОНКИ

Removal

PERFORMANCE ORDER

1. Disconnect an accelerator rope.

2. Disconnect an air branch pipe.

3. Disconnect a socket of connection of a potentiometer and vacuum hoses.

4. Turn off the top fixing screws (are specified by arrows) and remove the case throttle заслонки.

Installation

Installation is spent upside-down removals.

FUEL INJECTORS AND FUEL COLLECTOR

Removal

PERFORMANCE ORDER

1. Disconnect an air branch pipe from the case throttle заслонки.

2. Disconnect a rope of an accelerator and vacuum hoses.

3. Remove the case throttle заслонки.

4. Mark and disconnect fuel tubes and hoses.

5. Disconnect wires from injectors.

6. Turn off fixing bolts and remove a fuel collector.

Installation

Installation is spent upside-down removals.

REGULATOR OF PRESSURE OF FUEL

Removal

PERFORMANCE ORDER

1. Disconnect a vacuum hose.

2. Remove a fixing clip and remove a regulator.

Installation

Installation is spent upside-down removals.

THE OXYGEN GAUGE

Removal

PERFORMANCE ORDER

1. Disconnect a connection socket.

2. Unscrew the gauge.

Installation

Installation is spent upside-down removals.

THE ELECTRONIC BLOCK OF MANAGEMENT

Removal

PERFORMANCE ORDER

1. Remove panels of furnish and a casing of the electronic block of management.

2. Turn off fixing screws and remove the electronic block of management, having disconnected a connection socket.

Installation

Installation is spent upside-down removals.