Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
+ 3.1.1.2. Technical characteristics
+ 3.1.2. 5-cylinder engines
- 3.1.3. 6-cylinder engines
3.1.3.2. A gear belt
3.1.3.3. A head of cylinders
3.1.3.4. Valves
3.1.3.5. Replacement маслосъемных caps of valves
3.1.3.6. Check of directing valves
3.1.3.7. Fair processing of a landing facet of a saddle / the valve
3.1.3.8. Grinding in of saddles of valves
3.1.3.9. Compression check
3.1.3.10. A poliklinovoj belt
3.1.3.11. Greasing system
3.1.3.12. The oil pump
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice
|
Removal
| PERFORMANCE ORDER |
| 1. Remove a casing поликлинового a belt. For this purpose turn out 2 bolts SW 10 and unfasten a casing from the screen of coils of ignition. |
|
|
2. The engine with working volume 2,8 l and 30 valves (193 h.p.): Turn away the fan with вязкостной муфтой. For this purpose as a stopper insert into one of four apertures of a pulley поликлинового a belt a screw-driver and обоприте it on an arm of the fan with вязкостной муфтой. The Wrench turn on to the right (the left carving). Remove the fan. |
| |
3. Designate an arrow on поликлиновом a belt by means of a felt-tip pen or a marker a direction of its movement. The cranked shaft of the engine rotates if to look in front, to the right, that is in a direction clockwise. |
4. A klinovoj belt ослабьте. For this purpose turn the tension device, as is shown in drawing, in an arrow direction ring wrench SW 15 and stop a suitable pin (Ф 6 mm), for example, AUDI-3204. Preliminary a screw-driver remove a plastic cap from a tension roller.
The prevention At the engine capacity of 193 h.p. шестигранный a ring key of 17 mm insert under a tension roller, an arm of a tension roller turn to the right and stop.
|
| 5. A poliklinovoj belt remove. |
|
Installation
| PERFORMANCE ORDER |
1. Impose поликлиновой a belt at first on приводной and directing rollers and only then on a tension roller.
The prevention If the belt which was in the use is again established, it is necessary to pay attention to a direction of its movement. Belt installation in the opposite direction increases deterioration and can lead to its breakage. Therefore it is necessary поликлиновой to establish always a belt so that the put arrow showed in a direction of rotation of a shaft of the engine (if to look in front, in a direction clockwise).
|
| 2. Establish поликлиновой a belt on belt pulleys. Slightly press the tension device in an arrow direction. Pull out a plug-in pin. After that slowly turn натяжитель against an arrow direction, paying attention to correct position поликлинового of a belt on belt pulleys. |
| 3. The engine capacity of 193 h.p.: the Fan with вязкостной муфтой tighten to the left the moment of 40 Nanometers. |
| 4. Establish a casing поликлинового a belt. Establish a plastic cap on a tension roller. |
|
|
|
